Read online or download PDF. Page 19 / 24. Rockwell Automation 280D ArmorStart - Getting Started User Manual. Rockwell Automation Equipment. Manuals Directory ManualsDir.com - online owner manuals library. Rockwell Automation manuals.

Advertising

Publication 284G-QS001A-EN-P - December 2008

ArmorConnect Cable Ratings

Rockwell Automation 284 ArmorStart User Manual User Manual. Vfd type product codes and name strings. Rockwell Automation Equipment. Manuals Directory ManualsDir.com - online owner manuals. Appendix, Electronic data sheets – Rockwell Automation 284 ArmorStart User Manual User Manual Page 401: Vfd type product codes and name strings.
Allen-bradley ArmorStart 294E Pdf User Manuals. View online or download Allen-bradley ArmorStart 294E User Manual. Manuals; Brands; Allen-Bradley Manuals; Controller. Rockwell Automation Publication 290E-UM001B-EN-P - June 64. Optional Locking Clip 65. Product Commissioning 67. IP Address 67. Gateway Address 67.
ArmorStart, ArmorStart ST, ArmorStart LT, and Special Confuguration distributed motor controllers. Complete with diagrams. User manual 280E-UM001C. Rockwell Automation Support. Use the following resources to access support information. Documentation Feedback.

The ArmorConnect Power Media cables are rated per UL Type TC
600V 90 °C Dry 75 °C Wet, Exposed Run (ER) or MTW 600V 90 °C or
STOOW 105 °C 600V - CSA STOOW 600V FT2. For additional
information regarding ArmorConnect Power Media see the ArmorStart
User Manual.

Branch Circuit Protection Requirements for ArmorConnect™
Three-Phase Power Media

When using ArmorConnect Three-Phase Power Media, only fuses can be
used for the motor branch circuit protective device, for the group motor
installations. The recommended fuse types are the following: Class CC, T,
or J type fuses. For additional information, see the ArmorStart User
Manual. A 100 A circuit breaker can be used for the motor branch
protective device, for the group motor installations when using only the
following ArmorConnect power media components: 280-M35M-M1,
280-M35F-M1, 280-T35, and 280-PWRM35*-M*. For additional
information, see the ArmorStart User Manual.

Group Motor Installations for USA and Canada Markets

The ArmorStart Distributed Motor controllers are listed for use with each
other in group installations per NFPA 79, Electrical Standard for Industrial
Machinery. When applied according to the group motor installation
requirements, two or more motors, of any rating or controller type, are
permitted on a single branch circuit. Group Motor Installation has been
successfully used for many years in the USA and Canada.

Wiring and Workmanship Guidelines

In addition to conduit and seal-tite raceway, it is acceptable to utilize cable
that is dual rated Tray Cable, Type TC-ER and Cord, STOOW, for power
and control wiring on ArmorStart installations. In the USA and Canada
installations, the following guidance is outlined by the NEC and NFPA 79.

In industrial establishments where the conditions of maintenance and
supervision ensure that only qualified persons service the installation, and
where the exposed cable is continuously supported and protected against
physical damage using mechanical protection, such as struts, angles, or
channels, Type TC tray cable that complies with the crush and impact
requirements of Type MC (Metal Clad) cable and is identified for such use
with the marking Type TC-ER (Exposed Run)* shall be permitted between
a cable tray and the utilization equipment or device as open wiring. The
cable shall be secured at intervals not exceeding 1.8 m (6 ft) and installed in
a “good workman-like” manner. Equipment grounding for the utilization
equipment shall be provided by an equipment grounding conductor within
the cable.

Advertising

Popular Brands

Popular manuals

Advertising

Publication 284G-QS001A-EN-P - December 2008

DeviceNet Node

Commissioning

Establishing a DeviceNet Node Address

The ArmorStart is shipped with a default node address of 63 and Autobaud
enabled. Each device on a DeviceNet network must have a unique node
address or MAC ID which can be set to a value from 0…63. Keep in mind
that most DeviceNet systems use address 0 for the master device (Scanner)
and node address 63 should be left vacant for introduction of new slave
devices. The ArmorStart offers two methods for node commissioning as
shown in the following pages.

Node Commissioning using Software

Armorstart 284e Safety

To set the node address of the ArmorStart using software or other handheld
tools, leave the hardware rotary switches in their default position (99) or
insure that they are set to something greater then (63). With the hardware
switches set, use the software or handheld tool to change the address.

When using software to node commission a device, it may be necessary to
have the EDS file stored on the computer. The EDS file defines how the
software such as RSNetWorx for DeviceNet will communicate to the
ArmorStart. Rockwell Automation product EDS files are available on the
internet at: http://www.ab.com/networks/eds

Rockwell Automation Armorstart St User Manual

You must use RSNetWorx

for DeviceNet Revision 3.21 Service Pack 2 or later.

ATTENTION

Three-phase power must be applied to the Bulletin 284G
Distributed Motor Controller to gain access to drive
parameters.

Advertising

Armorstart 284e Manual

Popular Brands

Rockwell Armorstart Fault Codes

Popular manuals

Rockwell Automation Armorstart St User Manual